610T 610R

Kramer Electronics Detachable DVI Optical Transmitter & Receiver HandHeld

The 610T is a detachable optical transmitter and the 610R is a detachable optical receiver for sending DVI signals with a resolution of up to 1600x1200 at 60 Hz over LC optical cable. The 610T attaches to the transmitter side of a fiber optical cable and the 610R connects to the receiver end and are sold as a set.

• Max Data Rate - 1.65 Gbps
• System Range - Up to 500 meters (1640’)
• Cable - Multi-mode Fiber optic cable with 4 simplex or 2 duplex LC Fiber connectors.
• Input - 610T: DVI-D on a DVI-I connector. 610R: 4 LC optical connectors for R, G, B & Clock.
• Outputs - 610T: 4 LC optical connectors for R, G, B & Clock. 610R: DVI-D on a DVI-I connector
• Power - external power adapter (supplied) or 5V DC from source.

For more information, please click here.

Back to Top

611R

Kramer Electronics Fiber Optic Video Receiver TOOLS

The 611T and 611R are a high performance fiber optic transmitter and receiver for composite video signals. The 611T transmitter converts a composite video signal into a fiber optic signal and the 611T receiver will convert the fiber optic signal back into a composite video signal.

• Bandwidth - 55MHz (-3db).
• Level (Gain) and EQ (Peaking) Controls (611T & 611R).
• Multi-Mode - 5km (3.1 miles).
• Compact Size - Part of the Kramer Electronics TOOLS™ family of compact, high quality and cost effective solutions.

For more information please click here.

Back to Top

621R

Kramer Electronics DVI Optical Receiver TOOLS

The 621T and 621R are optical transmitter and receivers for DVI signals up to 1600x1200 at 60 Hz. The 621T converts a DVI signal into an optical signal and the 621R converts the optical signal back to DVI.

• Max Data Rate - 1.65 Gbps
• HDCP Compliant
• System Range - Up to 100 meters (320)
• Power Connect System - Only one unit in a system, the transmitter or receiver, needs to be connected to a power source. All the systems units must have Power Connect to use this feature.
• Cable - UTP (unshielded twisted pair) such as CAT5 and Fiber optic with 4 simplex or 2 duplex LC Fiber connectors.
• Compact Size - Part of the Kramer Electronics TOOLS family of compact, high quality and cost effective solutions.

For more information please click here.

Back to Top

622R

Kramer Electronics Dual Link DVI Optical Receiver Desktop

The 622T and 622R are optical transmitter and receivers for dual link DVI signals with resolutions up to 2560x1600 at 60 Hz. The 622T converts a DVI signal into an optical signal and the 622R converts the optical signal back to DVI.

• I/O - 8 simplex (or 4 duplex) LC optical connectors - 2 red, 2 green, 2 blue & 2 clock. 1 CAT5 (RJ-45) for DDC and HDCP bi-directional data.
• I/O - DVI-D on a DVI-I connector
• Max Data Rate - 3.3 Gbps Dual Link
• HDCP Compliant
• System Range - Up to 100 meters (320’)
• Power Connect™ System - Only one unit in a system, the transmitter or receiver, needs to be connected to a power source.
• Cable - UTP (unshielded twisted pair) such as CAT5 and Fiber optic with 8 simplex (or 4 duplex) LC Fiber connectors.
• Dual & single Link LED Indicators
• Desktop Size - Compact size. Two units can be rack mounted side-by-side in a 1U rack space with an optional rack adapter.

For more information please click here.

Back to Top

631R

Kramer Electronics HDMI Optical Receiver TOOLS

The 631T and 631R are optical transmitter and receivers for HDMI signals up to 1600x1200 at 60 Hz. The 631T converts a HDMI signal into an optical signal and the 631R converts the optical signal back to HDMI.

• Max Data Rate - 1.65 Gbps
• HDCP Compliant
• System Range - Up to 100 meters (320’)
• Power Connect™ System - Only one unit in a system, the transmitter or receiver, needs to be connected to a power source. All the systems units must have Power Connect to use this feature.
• Cable - UTP (unshielded twisted pair) such as CAT5 and Fiber optic with 4 simplex or 2 duplex LC Fiber connectors.
• Compact Size - Part of the Kramer Electronics TOOLS™ family of compact, high quality and cost effective solutions.

For more information please click here.

Back to Top

611T

Kramer Electronics Fiber Optic Video Transmitter TOOLS

The 611T and 611R are a high performance fiber optic transmitter and receiver for composite video signals. The 611T transmitter converts a composite video signal into a fiber optic signal and the 611T receiver will convert the fiber optic signal back into a composite video signal.

• Bandwidth - 55MHz (-3db).
• Level (Gain) and EQ (Peaking) Controls (611T & 611R).
• Multi-Mode - 5km (3.1 miles).
• Compact Size - Part of the Kramer Electronics TOOLS™ family of compact, high quality and cost effective solutions.

For more information please click here.

Back to Top

621T

Kramer Electronics DVI Optical Transmitter TOOLS

The 621T and 621R are optical transmitter and receivers for DVI signals up to 1600x1200 at 60 Hz. The 621T converts a DVI signal into an optical signal and the 621R converts the optical signal back to DVI.

• Max Data Rate - 1.65 Gbps
• HDCP Compliant
• System Range - Up to 100 meters (320)
• Power Connect System - Only one unit in a system, the transmitter or receiver, needs to be connected to a power source. All the systems units must have Power Connect to use this feature.
• Cable - UTP (unshielded twisted pair) such as CAT5 and Fiber optic with 4 simplex or 2 duplex LC Fiber connectors.
• Compact Size - Part of the Kramer Electronics TOOLS family of compact, high quality and cost effective solutions.

For more information please click here.

Back to Top

622T

Kramer Electronics Dual Link DVI Optical Transmitter Desktop

The 622T and 622R are optical transmitter and receivers for dual link DVI signals with resolutions up to 2560x1600 at 60 Hz. The 622T converts a DVI signal into an optical signal and the 622R converts the optical signal back to DVI.

• I/O- DVI-D on a DVI-I connector
• I/O - 8 simplex (or 4 duplex) LC optical connectors - 2 red, 2 green, 2 blue & 2 clock. 1 CAT5 (RJ-45) for DDC and HDCP bi-directional data.
• Max Data Rate - 3.3 Gbps Dual Link
• HDCP Compliant
• System Range - Up to 100 meters (320’)
• Power Connect™ System - Only one unit in a system, the transmitter or receiver, needs to be connected to a power source.
• Cable - UTP (unshielded twisted pair) such as CAT5 and Fiber optic with 8 simplex (or 4 duplex) LC Fiber connectors.
• Dual & single Link LED Indicators
• Desktop Size - Compact size. Two units can be rack mounted side-by-side in a 1U rack space with an optional rack adapter.

For more information please click here.

Back to Top

631T

Kramer Electronics HDMI Optical Transmitter TOOLS

The 631T and 631R are optical transmitter and receivers for HDMI signals up to 1600x1200 at 60 Hz. The 631T converts a HDMI signal into an optical signal and the 631R converts the optical signal back to HDMI.

• Max Data Rate - 1.65 Gbps
• HDCP Compliant
• System Range - Up to 100 meters (320’)
• Power Connect™ System - Only one unit in a system, the transmitter or receiver, needs to be connected to a power source. All the systems units must have Power Connect to use this feature.
• Cable - UTP (unshielded twisted pair) such as CAT5 and Fiber optic with 4 simplex or 2 duplex LC Fiber connectors.
• Compact Size - Part of the Kramer Electronics TOOLS™ family of compact, high quality and cost effective solutions.

For more information please click here.

Back to Top

648

Kramer Electronics FireWire® 800Mbps Fiber Optic Repeater TOOLS

The 648 is a high performance bi-directional optical repeater for FireWire 1394a and 1394b signals. When used in pairs, it will extend the distance of FireWire cable runs up to 500 meters.

• FireWire Ports - 2 bilingual 9-pin IEEE 1394b 800Mbps.
• Optical Ports - 2 duplex LC Fiber connectors.
• Range - Extends Firewire cable range from 14.5 ft (4.5 meters) to up to 1640 ft (500 meters) between 2 units.
• Transfer Rate - 100, 200, 400 and 800Mbps
• Compact Size - Part of the Kramer Electronics DigiTOOLs family of compact, high quality and cost effective solutions.

For more information please click here.

Back to Top

610T-610R

Kramer Electronics Detachable DVI Optical Transmitter & Receiver HandHeld

The 610T is a detachable optical transmitter and the 610R is a detachable optical receiver for sending DVI signals with a resolution of up to 1600x1200 at 60 Hz over LC optical cable. The 610T attaches to the transmitter side of a fiber optical cable and the 610R connects to the receiver end and are sold as a set.

• Max Data Rate - 1.65 Gbps
• System Range - Up to 500 meters (1640’)
• Cable - Multi-mode Fiber optic cable with 4 simplex or 2 duplex LC Fiber connectors.
• Input - 610T: DVI-D on a DVI-I connector. 610R: 4 LC optical connectors for R, G, B & Clock.
• Outputs - 610T: 4 LC optical connectors for R, G, B & Clock. 610R: DVI-D on a DVI-I connector
• Power - external power adapter (supplied) or 5V DC from source.

For more information, please click here.

Back to Top

621R

Kramer Electronics DVI Optical Receiver TOOLS

The 621T and 621R are optical transmitter and receivers for DVI signals up to 1600x1200 at 60 Hz. The 621T converts a DVI signal into an optical signal and the 621R converts the optical signal back to DVI.

• Max Data Rate - 1.65 Gbps
• HDCP Compliant
• System Range - Up to 100 meters (320)
• Power Connect System - Only one unit in a system, the transmitter or receiver, needs to be connected to a power source. All the systems units must have Power Connect to use this feature.
• Cable - UTP (unshielded twisted pair) such as CAT5 and Fiber optic with 4 simplex or 2 duplex LC Fiber connectors.
• Compact Size - Part of the Kramer Electronics TOOLS family of compact, high quality and cost effective solutions.

For more information please click here.

Back to Top

622R

Kramer Electronics Dual Link DVI Optical Receiver Desktop

The 622T and 622R are optical transmitter and receivers for dual link DVI signals with resolutions up to 2560x1600 at 60 Hz. The 622T converts a DVI signal into an optical signal and the 622R converts the optical signal back to DVI.

• I/O - 8 simplex (or 4 duplex) LC optical connectors - 2 red, 2 green, 2 blue & 2 clock. 1 CAT5 (RJ-45) for DDC and HDCP bi-directional data.
• I/O - DVI-D on a DVI-I connector
• Max Data Rate - 3.3 Gbps Dual Link
• HDCP Compliant
• System Range - Up to 100 meters (320’)
• Power Connect™ System - Only one unit in a system, the transmitter or receiver, needs to be connected to a power source.
• Cable - UTP (unshielded twisted pair) such as CAT5 and Fiber optic with 8 simplex (or 4 duplex) LC Fiber connectors.
• Dual & single Link LED Indicators
• Desktop Size - Compact size. Two units can be rack mounted side-by-side in a 1U rack space with an optional rack adapter.

For more information please click here.

Back to Top

VA-1DVI

Kramer Electronics DVI EDID Emulator TOOLS

The VA-1DVI is an EDID emulator for DVI-D signals. The unit can store and recall a default EDID setting in non-volatile memory from the output allowing convenient and reliable connection to the source.

• Max Data Rate - 1.65 Gbps
• Input/Output - DVI-D Signal on a DVI-I connectors
• Control - Capture button
• Compact Size - Part of the Kramer Electronics TOOLS family of compact, high quality and cost effective solutions

For more information please click here.

Back to Top

621T

Kramer Electronics DVI Optical Transmitter TOOLS

The 621T and 621R are optical transmitter and receivers for DVI signals up to 1600x1200 at 60 Hz. The 621T converts a DVI signal into an optical signal and the 621R converts the optical signal back to DVI.

• Max Data Rate - 1.65 Gbps
• HDCP Compliant
• System Range - Up to 100 meters (320)
• Power Connect System - Only one unit in a system, the transmitter or receiver, needs to be connected to a power source. All the systems units must have Power Connect to use this feature.
• Cable - UTP (unshielded twisted pair) such as CAT5 and Fiber optic with 4 simplex or 2 duplex LC Fiber connectors.
• Compact Size - Part of the Kramer Electronics TOOLS family of compact, high quality and cost effective solutions.

For more information please click here.

Back to Top

622T

Kramer Electronics Dual Link DVI Optical Transmitter Desktop

The 622T and 622R are optical transmitter and receivers for dual link DVI signals with resolutions up to 2560x1600 at 60 Hz. The 622T converts a DVI signal into an optical signal and the 622R converts the optical signal back to DVI.

• I/O- DVI-D on a DVI-I connector
• I/O - 8 simplex (or 4 duplex) LC optical connectors - 2 red, 2 green, 2 blue & 2 clock. 1 CAT5 (RJ-45) for DDC and HDCP bi-directional data.
• Max Data Rate - 3.3 Gbps Dual Link
• HDCP Compliant
• System Range - Up to 100 meters (320’)
• Power Connect™ System - Only one unit in a system, the transmitter or receiver, needs to be connected to a power source.
• Cable - UTP (unshielded twisted pair) such as CAT5 and Fiber optic with 8 simplex (or 4 duplex) LC Fiber connectors.
• Dual & single Link LED Indicators
• Desktop Size - Compact size. Two units can be rack mounted side-by-side in a 1U rack space with an optional rack adapter.

For more information please click here.

Back to Top

PS-1DVI

Kramer Electronics DVI Power Supply MultiTOOLS

The PS-1DVI is a high performance power supply for DVI cables. It provides 5V DC on pin 14 for applications where power is not provided by the DVI source.

• Max Data Rate - 3Gbps Dual Link
• Input/Output - DVI-I connectors
• Works with Kramer Electronics Optical DVI Cables - Optical DVI Cables such as the Kramer Electronics C-FODM/FODM-XX require 5V DC to power the electronics in the DVI connectors
• Compact Size - Part of the MultiTOOLS™ family of compact, high quality and cost effective solutions.

For more information please click here.

Back to Top

WPN-11

Kramer Electronics Computer Graphics Video and Component Video Transmitter & Wall Plate Wallplate

The WPN-11 is a transmitter for computer graphics video with resolutions ranging from VGA through UXGA and higher, component video, s-Video (Y/C) or composite video signals. It is used in conjunction with a WPN-12 receiver.

• High Bandwidth - 450MHz (-3db)
• HDTV Compatible
• Front Panel Connections - 15-pin HD and 3 RCAs for component video, s-Video (Y/C) or composite video inputs
• Rear Panel Connections - Terminal block output
• Control - Input selection
• Wall Plate - Single gang

For more information please click here.

Back to Top

WP-211DS

Kramer Electronics 2x1 Computer Graphics & Stereo Audio Standby Switcher, Twisted Pair Transmitter & Wall Plate Wallplate

The WP-211DS is a high performance switcher for computer graphics video signals with resolutions ranging from VGA through UXGA and higher, and unbalanced stereo audio signals. When configured as a standby switcher, it will switch to the secondary input upon loss of the primary input.

• High Bandwidth - 300MHz (-3db)
• HDTV Compatible
• Automatic Standby Switching - It will switch from secondary input to primary input when a signal is detected
• Power Connect™ System - Only one unit in a system, the transmitter or the receiver needs to be connected to a power source. All the system units must have the Power Connect system to use this feature.
• Front Panel Connections - Dual 15-pin HD and dual 3.5mm inputs
• Rear Panel Connections - Terminal block outputs for stereo audio, contact closure control, and RGBHV and Twisted Pair for computer graphics video.
• Looping Input - Input 1
• Control - Automatic or contact closure switching and output disconnect with LED status indicator
• ID Bit Control
• System Range - CAT5 up to 100 meters (320’)
• Twisted Pair Cable - UTP (unshielded twisted pair) such as CAT5.
• Wall Plate - 3 gang

For more information please click here.

Back to Top

WV-11N

Kramer Electronics Composite Video over Twisted Pair Transmitter & Wall Plate Wallplate

The WV-11N is a wall plate for composite video signals. It will convert a composite video input to a twisted pair signal which will be converted back to composite video with a WV-12N twisted pair receiver.

• Front Panel Connections - BNC (F) input.
• Rear Panel Connections - 3-pole and 2-pole Terminal Block output.
• Level (Gain) and EQ (Peaking) Controls.
• Wall Plate Size - Single gang.

For more information please click here.

Back to Top

WV-12N

Kramer Electronics Twisted Pair to Composite Video Receiver & Wall Plate Wallplate

The WV-12N is a wall plate for composite video signals. It will convert a twisted pair signal from a WV-11N twisted pair transmitter back into a composite video signal.

• Front Panel Connections - BNC (F) output.
• Rear Panel Connections - 3-pole and 2-pole terminal block input.
• Level (Gain) and EQ (Peaking) Controls.
• Wall Plate Size - Single gang.

For more information please click here.

Back to Top

WPN-12

Kramer Electronics Computer Graphics Video and Component Video Receiver & Wall Plate Wallplate

The WPN-12 is a receiver for computer graphics video with resolutions ranging from VGA through UXGA and higher, component video, s-Video (Y/C) or composite video signals. It is used in conjunction with a WPN-11 transmitter.

• High Bandwidth - 450MHz (-3db)
• HDTV Compatible
• Front Panel Connections - 15-pin HD and 3 RCAs for component video, s-Video (Y/C) or composite video outputs
• Rear Panel Connections - Terminal block input
• Wall Plate - single gang

For more information please click here.

Back to Top

WP-110

Kramer Electronics Computer Graphics Video to Twisted Pair Transmitter & Wall Plate Wallplate

The WP-110 is a twisted pair transmitter for computer graphic video signals with resolutions ranging from VGA through UXGA and higher. It converts a computer graphics video signal into a twisted pair signal which will be converted back into a computer graphic signal when used in conjunction with the TP-120 twisted pair receiver (or other compatible Kramer Electronics receiver).

• Resolution - Up to UXGA
• HDTV Compatible
• Power Connect™ System - Only one unit in a system, the transmitter or the receiver needs to be connected to a power source. All the system units must have the Power Connect system to use this feature.
• Advanced Sync Processing - Ensures compatibility with a wide range of computers.
• Front Panel Connections - 15-pin HD input
• Rear Panel Connections - RJ-45 output
• Selectable Sync Input Impedance - 75 Ώ (analog) or 510 Ώ (TTL)
• System Range - Up to 100 meters (320’)
• Cable - UTP (unshielded twisted pair) such as CAT5.
• Wall Plate - Single gang

For more information please click here.

Back to Top

WA-20N

Kramer Electronics Unbalanced to Balanced Stereo Audio over Twisted Pair Receiver & Wall Plate Wallplat

The WA-20N is a wall plate for stereo audio signals. It will convert a balanced twisted pair signal from a WA-23N twisted pair transmitter back into a stereo audio signal.

• Front Panel Connections - Dual RCA (F) output.
• Rear Panel Connections - 6-pole terminal block input.
• Termination Switch - Allows operation of multiple WA-20Ns from a common source.
• Wall Plate Size - Single gang.

For more information please click here.

Back to Top

WA-21N

Kramer Electronics Unbalanced to Balanced Stereo Audio over Twisted Pair Transmitter & Wall Plate Wallplate

The WA-21N is a wall plate for stereo audio signals. It will convert an unbalanced stereo audio input to balanced stereo audio output over twisted pair which will be converted back to a stereo audio signal with a WA-22 twisted pair receiver.

• Front Panel Connections - 3.5mm (F) input.
• Rear Panel Connections - 6-pole terminal block output.
• Audio Level Controls - Left & right.
• Wall Plate Size - Single gang.

For more information please click here.

Back to Top

WA-22N

Kramer Electronics Balanced to Unbalanced Stereo Audio over Twisted Pair Receiver & Wall Plate Wallplate

The WA-22N is a wall plate for stereo audio signals. It will convert a balanced twisted pair signal from a WA-21N twisted pair transmitter back into a stereo audio signal.

• Front Panel Connections - 3.5mm (F) output
• Rear Panel Connections - 6-pole and 2-pole terminal block input
• Termination Switch - Allows operation of multiple WA-22s from a common source.
• Audio Level Controls - Left & right.
• Wall Plate Size - Single gang.

For more information please click here.

Back to Top

WA-23N

Kramer Electronics Unbalanced to Balanced Stereo Audio over Twisted Pair Transmitter & Wall Plate Wallplate

The WA-23N is a wall plate for stereo audio signals. It will convert an unbalanced stereo audio input to balanced stereo audio output over twisted pair which will be converted back to a stereo audio signal with a WA-20N twisted pair receiver.

• Front Panel Connections - Dual RCA (F) inputs.
• Rear Panel Connections - 6-pole and 2-pole terminal block output.
• Audio Level Controls - Left & right.
• Wall Plate Size - Single gang.

For more information please click here.

Back to Top

WP-210

Kramer Electronics Computer Graphics Video Line Driver and Wall Plate Wallplate

The WP-210 is a wall plate line driver for computer graphics video signals with resolutions ranging from VGA through UXGA and higher. It provides controls to compensate for signal losses inherent in long cable runs.

• High Bandwidth - 400KHz (-3dB).
• HDTV Compatible
• Advanced Sync Processing - Ensures compatibility with a wide range of computers.
• Front Panel Connections -15-pin HD input
• Rear Panel Connections - 5 BNC output
• Looping Input.
• Input Signal Termination
• Selectable Sync Input Impedance - 75 Ώ (analog) or 510 Ώ (TTL)
• ID Bit Control.
• EQ (Peaking) Control.
• Wall Plate Size - Single gang.

For more information please click here.

Back to Top

WP-210E

Kramer Electronics XGA Line Driver Wallplate

XGA Line Driver wall plate with a VGA/UXGA looping input (HD-15) and an amplified and equalized RGBHV output with cable EQ. level, ID bit and termination controls.

For more information please click here.

Back to Top

WP-220E

Kramer Electronics XGA/Video/Audio Line Driver Wallplate

XGA/Video/Audio Line Driver wall plate with a VGA/UXGA input (HD-15), Composite video input and two stereo audio inputs – one on RCAs, one on a mini 3.5mm socket (from PC) and an amplified and equalized RGBHV output with cable EQ., a CV output with cable EQ. and two balanced stereo outputs, one with R&L level controls.

For more information please click here.

Back to Top

VPM-2

Kramer Electronics Computer Graphics Video Line Driver & Wall Plate TOOLS

The VPM-2 is a wall plate line driver for computer graphics video signals with resolutions ranging from VGA through UXGA and higher. Multiple units can be connected to a Kramer Electronics switcher (such as the VP-81xl).

• High Bandwidth - 380MsHz (- 3dB).
• HDTV Compatible.
• Front Panel Connections -15-pin HD input
• Rear Panel Connections - 15-pin HD output
• Looping Input.
• Remote Switcher Input Control - Contact closure sent to Kramer Electronics switcher (such as VP-81N) to activate input from wall plate.
• ID Bit Control.
• EQ (Peaking) Control.
• Auxiliary Inputs - 3 removable panels which can be replaced with passive Kramer Electronics “WP” series wall plate input modules.
• Wall Plate Size - 4 gang.

For more information please click here.

Back to Top

WP-210AL

Kramer Electronics Computer Graphics Video Line Amplifier with Stereo Audio & Wall Plate Wallplate

The WP-210AL is a line driver for computer graphics video with resolutions from VGA through UXGA and higher along with stereo audio signals. The set-up controls are located on the front panel.

• High Bandwidth - 350MHz (-3dB)
• Inputs - 15-pin HD (for VGA/UXGA) and 3.5mm (for stereo audio)
• Looping Input - VGA/UXGA
• Input Signal Termination
• Outputs - RGBHV (on BNCs) and Terminal block (for Balanced stereo audio).
• Front Panel Controls - All controls are located on the front panel for convenient adjustment.
• Level (Gain) and EQ Peaking Controls.
• Advanced Sync Processing - Ensures compatibility with a wide range of computers.
• Selectable Sync Input Impedance - 75 Ώ (analog) or 510 Ώ (TTL)
• Audio Level Controls - Left & Right.
• Active Input LED Indicator
• ID Bit Control.
• Wall Plate Size - Single gang.
• HDTV Compatible
• Front Panel Connections - 15-pin HD (for VGA/UXGA) and 3.5mm (for stereo audio) inputs
• Rear Panel Connections - 5 BNCs and terminal block (for Balanced stereo audio).

For more information please click here.

Back to Top

WP-220

Kramer Electronics Computer Graphics & Video Line Amplifier with Audio & Wall Plate Wallplate

The WP-220 is a line driver for computer graphics video with resolutions from VGA through UXGA and higher and composite video, each with stereo audio signals. It provides controls to compensate for signal losses inherent in long cable runs.

• High Bandwidth - 500MHz (-3dB) for 15-pin HD and 490MHz (-3db) for composite video.
• HDTV Compatible
• Advanced Sync Processing - Ensures compatibility with a wide range of computers.
• Front Panel Connections - 15-pin HD (PC) with 3.5mm stereo Audio and RCA for composite video with 2 RCAs for stereo Audio inputs.
• Rear Panel Connections - 5 BNCs for the computer graphics signals, terminal blocks for the composite video signal, and Balanced stereo terminal blocks for each stereo Audio signal.
• Level (Gain) and EQ (Peaking) Controls.
• Audio Level Controls - Left & Right for stereo Audio on 2 RCAs
• Wall Plate Size - Single gang.

For more information please click here.

Back to Top

WP-230

Kramer Electronics Computer Graphics, Video and Audio Line Driver & Wall Plate Wallplate

The WP-230 is a wall plate line driver for computer graphics video signals with resolutions from VGA through UXGA and higher, composite video, s-Video (Y/C) signals and stereo audio signals. It provides controls to compensate for signal losses inherent in long cable runs.

• High Bandwidth - 520MHz (-3dB) for 15-pin HD, 438MHz (-3db) for composite video & 155Mhz (-3db) for Y/C.
• HDTV Compatible
• Front Panel Connections - 15-pin HD (PC) with 3.5mm stereo Audio and RCA for composite video and 4-pin for Y/C with 2 RCAs for stereo Audio inputs. RJ-45 (Pass-through).
• Rear Panel Connections - 5 BNCs for the computer graphics signals, terminal blocks for the composite video and Y/C signals, and Balanced stereo terminal blocks for each stereo Audio signal. RJ-45 (pass-through).
• Level (Gain) Control - Line level Audio from 2 RCAs, composite video and s-Video (both Y and C).
• EQ (Peaking) Control - 15-pin HD & composite video
• Audio Level Controls - Left & Right for stereo Audio on 2 RCAs
• Wall Plate Size - Single gang.

For more information please click here.

Back to Top

WV-20N

Kramer Electronics 1:2 Composite Video over Twisted Pair Line and Distribution Amplifier & Wall Plate Wallplate

The WV-20N is a wall plate for composite video signals. It will convert a composite video input to two twisted pair signals which will be converted back to composite video with two WV-12N twisted pair receivers.

• Front Panel Connections - BNC (F) input.
• Rear Panel Connections - 4-pole terminal block output.
• Level (Gain) and EQ (Peaking) Controls.
• Wall Plate Size - Single gang.

For more information please click here.

Back to Top

RC-2

* New Product - August 2009 *

Kramer Electronics Wall Plate - RS-232 Controller

The RC-2 is a 2-button controller that sends a series of RS-232 commands with a push of a button. It operates serial-controllable devices such as projectors, displays, switchers, and so on.

• 2 Back Lit & Label Capable Buttons
• 1 RS-232 Port - Controls a device via serial control protocols
• Easily add control ports by adding the PL-18 control port expander
• Memory - Each button can be programmed with up to four macro sequences
• Wall Plate - 1 Gang.

For more information please click here.

Back to Top

RC-8IR

Kramer Electronics 8-Button Universal Room Controller with IR Learning Wallplate

The RC-8 IR is an 8-button room controller for multimedia rooms. It will control audio components, video components and other room facilities such as lights and screens.

• Configurable Back-Lit Buttons – Functions and/or macros are programmed into the 8 buttons which can be labeled for easy operation.
• Command Programming - IR learning or Ethernet.
• Control Options- 1 Ethernet, 2 RS-232, 4 (2x2) IR Emitters, 1 RS-485 & 2 Relays.
• Macro Mode - up 15 commands with a single button (maximum 120 commands).
• Wall Plate Size.

For more information please click here.

Back to Top

RC-1000N

Kramer Electronics Master Programmable Remote Control Panel Wallplate

The RC-1000N is a programmable remote control for Kramer Electronics switchers with RS-232 and RS-485 control interfaces. This wall plate unit can control up to 16 matrix switchers.

• Configurable Back-Lit Buttons
• Take/Machine # Button - Select the Switcher to control and execute multiple switches with one button.
• Front Panel Lockout
• Flexible Control Options - Front Panel, 3 RS-232 (1 for PC control & 2 for Switcher control), 1 RS-485 (for machine control).
• Standard 2 gang size Wall Plate.

For more information please click here.

Back to Top

WAP-1

Kramer Electronics 2x1 Stereo Audio Switcher, Power Amplifier & Wallplate

The WAP-1 is a high performance power amplifier for line level unbalanced stereo audio signals. It delivers a speaker output of 9 watts RMS per channel into a 4 ohm load.

• Front Panel Connections - Dual 3.5mm inputs for inputs 1 and 2
• Rear Panel Connections - Terminal blocks for secondary input (input 1) and terminal blocks for two speakers outputs.
• Control - Level (volume)
• Wall Plate - single gang

For more information please click here.

Back to Top

WAV-5YC

Kramer Electronics Computer Graphics, S-video & Stereo Audio Wall Plate

• Front – 1 15-Pin HD (F), 1 4-Pin (F), 1 3.5mm (F), 2 RCA (F)
• Rear – 1 15-Pin HD (F), 1 4-Pin (F), 1 3.5mm (F), 2 RCA (F)
• Wallplate

For more information please click here

Back to Top

W-HDMI

Kramer Electronics HDMI Wall Plate Insert

• Front – 1 HDMI (F)
• Rear – 1 HDMI (F)
• Wallplate

For more information please click here

Back to Top

WAV-5C

Kramer Electronics Computer Graphics Video , Composite Video, & Stereo Audio Wall Plate

• Front – 1 15-Pin HD (F), 1 3.5mm (F), 3 RCA (F)
• Rear – 5 BNC (F), 1 3.5mm (F), 3 RCA (F)
• Wallplate

For more information please click here.

Back to Top

WAV-6UBA

Kramer Electronics Computer Graphics, USB, Composite Video & Stereo Audio Wall Plate

• Front – 1 15-Pin HD (F), 1 USB-B (F), 1 3.5mm (F), 3 RCA (F)
• Rear – 1 15-Pin HD (F), 1 USB-A (F), 1 3.5mm (F), 3 RCA (F)
• Wallplate

For more information please click here.

Back to Top

WS-3P

Kramer Electronics s-Video & Stereo Audio Wall Plate Insert

• Front – 1 4-Pin (F), 2 RCA (F)
• Rear – 1 4-Pin (F), 2 RCA (F)
• Wallplate

For more information please click here

Back to Top

WXA-2P

Kramer Electronics Computer Graphics Video & Stereo Audio Wall Plate

• Front – 1 15-Pin HD (F), 1 3.5mm
• Rear – 1 15-Pin HD (F), 1 3.5mm
• Wallplate

For more information please click here

Back to Top

WCP

Kramer Electronics Cable Pass Through

• Front – 1 cable
• Rear – 1 cable
• Wallplate

For more information please click here.

Back to Top

WU-AB

Kramer Electronics USB Wall Plate Insert

• Front – 1 USB (A)
• Rear – 1 USB (B)
• Wallplate

For more information please click here

Back to Top

WAV-5HDMI

Kramer Electronics Passive Wall Plate - HDMI, s-Video & 3 RCA

• Front – 1 HDMI (F), 1 4-Pin (F), 3 RCA (F)
• Rear – 1 HDMI (F), 1 4-Pin (F), 3 RCA (F)
• Wallplate

For more information please click here.

Back to Top

WA-1XLF

Kramer Electronics XLR Wall Plate Insert

Front Panel Connections - XLR (M)
Rear Panel Connections - Solder Cups to Wires
Size - Dual insert

For more information please click here

Back to Top

WA-1XLM

Kramer Electronics XLR Wall Plate Insert

Front Panel Connections - XLR (M)
Rear Panel Connections - Solder Cups to Wires
Size - Dual insert

For more information please click here

Back to Top

WA-2F

Kramer Electronics Dual F Connector Wall Plate Insert

Front Panel Connections - Dual F Connector (F).
Rear Panel Connections - Dual F Connector (F).
Size – Single insert

For more information please click here.

Back to Top

WA-1F

Kramer Electronics F Connector Wall Plate Insert

Front Panel Connections - F Connector (F).
Rear Panel Connections - F Connector (F).
Size – Single insert

For more information please click here.

Back to Top

WU-BB

Kramer Electronics USB Wall Plate Insert

Front Panel Connections - USB Type B (F)
Rear Panel Connections - USB Type A (F) on a flexible cable
Size – Single insert

For more information please click here.

Back to Top

WA-BA

Kramer Electronics USB Wall Plate Insert

Front Panel Connections - USB Type B (F)
Rear Panel Connections - USB Type A (F) on a flexible cable
Size – Single insert

For more information please click here.

Back to Top

WP-209

Kramer Electronics Computer Graphics Video, Composite Video, Stereo Audio & Network Wall Plate

The WP-209 is a wall plate for computer graphics video and composite video, each with stereo audio and network signals on RJ-45 connectors. The computer graphics video input has a local monitor output.

• Resolution - Up to UXGA
• HDTV Compatible
• Front Panel Connections - 15-pin HD (F) looping input and 3.5mm (F) connectors plus three RCAs (F) and RJ-45 pass-through connectors
• Rear Panel Connections - 15-pin HD (F) connector mounted to a short and extremely flexible cable, balanced stereo audio on a 5-pin terminal block connector plus 3 RCAs (F) and an RJ-45 pass through connectors
• Level (Gain) & EQ (Peaking) Control
• Audio Level Controls - Left & Right
• Wall Plate Size - Dual Gang

For more information please click here.

Back to Top

WAS-4

Kramer Electronics Composite Video, s-Video & Stereo Audio Wall Plate Insert

• Front Panel Connections - 4-pin (F) s-Video and three RCA (F) connectors (yellow, red & white)
• Rear Panel Connections - Two 4-pin terminal blocks
• Insert Size - Double insert

For more information please click her

Back to Top

WAS-3

Kramer Electronics s-Video & Stereo Audio Wall Plate Insert

• Front Panel Connections - 4-pin (F) s-Video and two RCA (F) connectors
• Rear Panel Connections - 4-pin (F) s-Video and two RCA (F) connectors
• Insert Size - Double Insert

For more information please click here

Back to Top

WAV-1R

Kramer Electronics Composite Video & Stereo Audio Wall Plate Insert
Single Sized WP Module

• Front Panel Connections - RCA (F) and 3.5mm (F) connectors.
• Rear Panel Connections - 3-pin and 2-pin terminal blocks.
• Single Sized WP Module.

For more information please click here

Back to Top

WAV-6YC

Kramer Electronics Computer Graphics Video, Composite Video, s-Video & Stereo Audio Wall Plate

• Front Panel Connections - 15-pin HD (F), 3.5mm (F), three RCA (F) and 4-pin Mini DIN (F) connectors
• Rear Panel Connections - 15-pin HD (F), 3.5mm (F), three RCA (F) and 4-pin Mini DIN (F) connectors
• Wall Plate Size - Single gang

For more information please click here

Back to Top

WAV-2

Kramer Electronics 3 Composite Video & 1 Stereo Audio Passive Wall Plate Insert

A wall plate that has on the front three video inputs (YUV, Composite, YC, RGB) on RCAs and a 3.5mm stereo audio socket. On the back it has terminal block connectors.

• Front Panel Connections - 3 RCA (F) and 1 3.5mm (F).
• Rear Panel Connections - 3-pole and a 6-pole terminal block.
• Wall Plate Size - Single gang.

For more information please click here.

Back to Top

WVS-2

Kramer Electronics Composite Video, s-Video & Dual Stereo Audio Passive Wall Plate

A wall plate that has on the front YC (s-Video), CV (RCA) and 2 x 3.5mm stereo audio connectors. On the back it has terminal block connectors.

• Front Panel Connections - RCA (F), 4-pin Mini-DIN (F) and dual 3.5mm (F)
• Rear Panel Connections - Dual 6-pin terminal block output.
• Wall Plate Size - Single gang.

For more information please click here.

Back to Top

WXV-1

Kramer Electronics Composite Video & Computer Graphics Video Passive Wall Plate

A wall plate that has on the front XGA (HD-15), CV (RCA) connectors. On the back it has terminal block connectors.

• Front Panel Connections - RCA (F) and 15-pin HD (F).
• Rear Panel Connections - Dual 6-pole terminal block.
• Wall Plate Size - Single gang.

For more information please click here.

Back to Top

WXL-2F

Kramer Electronics XLR to Terminal BLock Adapter Wallplate

A wall plate that has a female (WXL-1F) or two female (WXL-2F) XLR connectors on the front and terminal block connectors on the back.

• Front Panel Connections - Dual XLR (F).
• Rear Panel Connections - 6-pole terminal block.
• Wall Plate Size - Single gang.

For more information please click here.

Back to Top

WVS-1

Kramer Electronics s-Video & Stereo Audio Passive Wall Plate

A wall plate that has on the front a YC (s-Video) connector and two RCAs for audio. On the back it has terminal block connectors.

• Front Panel Connections - 4-pin Mini-DIN (F) and dual RCA (F)
• Rear Panel Connections - 8-pole terminal block.
• Wall Plate Size - Single gang.

For more information please click here.

Back to Top

WXA-1

Kramer Electronics Computer Graphics Video & Stereo Audio Passive Wall Plate

A wall plate that has on the front an XGA (HD-15) and a 3.5mm stereo audio connector. On the back it has terminal block connectors.

• Front Panel Connections - 15-pin HD (F) and 3.5mm (F)
• Rear Panel Connections - Dual 6-pole terminal block.
• Wall Plate Size - Single gang.

For more information please click here.

Back to Top

WXL-1FM

Kramer Electronics XLR Passive Wall Plate

A wall plate with female and male XLR connectors on the front and terminal block connectors on the back.

• Front Panel Connections - XLR (F) and XLR (M).
• Rear Panel Connections - 6-pole terminal block.
• Wall Plate Size - Single gang.

For more information please click here.

Back to Top

WXL-2FM

Kramer Electronics One or Two Male XLR Audio to Terminal Blocks Adapter Wallplate

A wall plate that has a male (WXL-1M) or two male (WXL-2M) XLR connectors on the front and terminal block connectors on the back.

• Front Panel Connections - Dual XLR (M).
• Rear Panel Connections - 6-pole terminal block.
• Wall Plate Size - Single gang.

For more information please click here.

Back to Top

W-DVIA

* New Product - August 2009 *

Kramer Electronics Wall Plate Insert - DVI & RCA

DVI-I & S/PDIF Audio Wall Plate Insert

• Front Panel Connections - DVI-I (F) & 3.5mm (F)
• Rear Panel Connections - DVI-I (F) cable & 3.5mm (F) cable
• Size - Dual slot wall plate insert

For further information click here

Back to Top

WAV-DA2

* New Product - August 2009 *

Kramer Electronics Passive Wall Plate - DVI & Dual RCA

DVI & Stereo Audio Passive Wall Plate

• Front Panel Connections - DVI (F) & 2 RCA (F)
• Rear Panel Connections - DVI (F) on a flat, flexible cable & 2 RCA (F)
• Available in Gray, White & Off White

For further information click here

Back to Top

WBR

Kramer Electronics BNC and RCA Pass Through Wallplate

BNC and RCA Pass Through

• Front Panel Connections - BNC (F) and RCA (F)
• Rear Panel Connections - BNC (F) and RCA (F)
  

For more information please click here

Back to Top

WB-45

Kramer Electronics BNC and RJ-45 Pass Through Wallplate

BNC and RJ-45 Pass Through

• Front Panel Connections - RJ-45 & BNC (F).
• Rear Panel Connections - RJ-45 & BNC (F).

For more information please click here.

Back to Top

WV-2N

Kramer Electronics Dual BNC to Terminal Block Adapter Wallplate

A dual BNC to 3-pole terminal block adapters for connecting two video sources.

• Front Panel Connections - Dual BNC (F).
• Rear Panel Connections - Dual 3-pole terminal block.

For more information please click here.

Back to Top

WAV-1N

Kramer Electronics BNC+ Mini Headphone Connector to Terminal Block Adapter

A BNC and a 3.5mm mini headphone connector to two 3-pole terminal blocks, for connecting video and stereo audio.

• Front Panel Connections - 3.5mm (F) and BNC (F).
• Rear Panel Connections - Dual 3-pole terminal block.

For more information please click here.

Back to Top

WBB

Kramer Electronics Double BNC Pass Through Wallplate

Double BNC Pass Through

• Front Panel Connections - Dual BNC (F)
• Rear Panel Connections - Dual BNC (F)

For more information please click here.

Back to Top

WX-F5B

Kramer Electronics Computer Graphics Video Wall Plate Insert Wallplate

An HD-15 (VGA through UXGA) connector to 5 BNCB connector for connecting a graphics source.

• Front Panel Connections - 15-pin HD (F)
• Rear Panel Connections - 5 BNC (F)

For more information please click here.

Back to Top

WRR

Kramer Electronics RC and RJ-45 Pass Through Wallplate

RCA and RJ-45 Pass Through

• Front Panel Connections - RCA (F) and RJ-45.
• Rear Panel Connections - RCA (F) and RJ-45.

For more information please click here.

Back to Top

WR-45

Kramer Electronics RC and RJ-45 Pass Through Wallplate

RCA and RJ-45 Pass Through

• Front Panel Connections - RCA (F) and RJ-45.
• Rear Panel Connections - RCA (F) and RJ-45.

For more information please click here.

Back to Top

WA-2N

Kramer Electronics Dual RCA to Terminal Block Adapter Wallplat

A dual RCA to a 4-pole terminal block adapter for connecting a stereo audio signal.

• Front Panel Connections - Dual RCA (F).
• Rear Panel Connections - 4-pole terminal block.

For more information please click here.

Back to Top

WBR

Kramer Electronics BNC and RCA Pass Through Wallplate

BNC and RCA Pass Through

• Front Panel Connections - BNC (F) and RCA (F).
• Rear Panel Connections - BNC (F) and RCA (F).

For more information please click here.

Back to Top

WAS-1N

Kramer Electronics 4p + Mini Headphone Connectors to Terminal Block Adapter

An s-Video (on a “4p” connector) and a 3.5mm mini headphone connector to two 3-pole terminal block, for connecting s-Video and stereo audio.

• Front Panel Connections - 3.5mm (F) and 4-pin Mini-DIN (F).
• Rear Panel Connections - Dual 3-pole terminal block.

For more information please click here.

Back to Top

WX-2F

Kramer Electronics Female VGA to Female VGA Wallplate

Female VGA to Female VGA

• Front Panel Connections - 15-pin HD (F)
• Rear Panel Connections - 15-pin HD (F)

For more information please click here.

Back to Top

WX-MF

Kramer Electronics Male VGA to Female VGA connection module Wallplate

Male VGA to Female VGA connection module on HD-15 connector.

• Front Panel Connections - 15-pin HD (M)
• Rear Panel Connections - 15-pin HD (F)

For more information please click here

Back to Top

WX-F5B

Kramer Electronics Computer Graphics Video Wall Plate Insert Wallplate

An HD-15 (VGA through UXGA) connector to 5 BNCB connector for connecting a graphics source.

• Front Panel Connections - 15-pin HD (F)
• Rear Panel Connections - 5 BNC (F)

For more information please click here.

Back to Top

WX-1N

Kramer Electronics 15-pin HD to Terminal Block Adapter (VGA through UXGA) Wallplate

A 15-pin HD (VGA through UXGA) connector to a 6 + 2 terminal block connector for connecting a graphics source. The adapter includes a switch for ID bit control.

• Front Panel Connections - 15-pin HD (F).
• Rear Panel Connections - 6-pole and 2-pole terminal block.

For more information please click here

Back to Top

WX-2M

Kramer Electronics Male VGA to Male VGA Wallplate

Male VGA to Male VGA

• Front Panel Connections - 15-pin HD (M)
• Rear Panel Connections - 15-pin HD (M)

For more information please click here.

Back to Top

WX-FM

Kramer Electronics Female VGA to Male VGA Wallplate

Female VGA to Male VGA connection module on HD-15 connector

• Front Panel Connections - 15-pin HD (F).
• Rear Panel Connections - 15-pin HD (M).

For more information please click here.

Back to Top

WB-45

Kramer Electronics BNC and RJ-45 Pass Through Wallplate

BNC and RJ-45 Pass Through

• Front Panel Connections - RJ-45 & BNC (F).
• Rear Panel Connections - RJ-45 & BNC (F).

For more information please click here.

.

Back to Top

W-4545

Kramer Electronics Dual Ethernet Wall Plate Insert Wallplate

Dual Ethernet Wall Plate Insert

• Front Panel Connections - Dual RJ-45
• Front Panel Connections - Dual RJ-45

For more information please click here.

Back to Top

WR-45

Kramer Electronics RCA and RJ-45 Pass Through Wallplate

RCA and RJ-45 Pass Through

• Front Panel Connections - RCA (F) and RJ-45
• Rear Panel Connections - RCA (F) and RJ-45

For more information please click here.

Back to Top

W-1145

Kramer Electronics RJ-11 and RJ-45 Pass Through Wallplate

RJ-11 and RJ-45 Pass Through

• Front Panel Connections - RJ-11 & RJ-45
• Rear Panel Connections - RJ-11 & RJ-45

For more information please click here.

Back to Top

WSP-1

Kramer Electronics Loudspeaker Wall Plate Insert Wallplate

A 4-pole adapter between loudspeakers cables. Fits into a wallplate frame.

• Front Panel Connections - 4-pole with clips.
• Rear Panel Connections - 4-pin terminal block.

For more information please click here.

Back to Top

WA-1N

Kramer Electronics Terminal Block Adapter for Balanced Stereo Audio Wallplate

A 6-pole terminal block on both sides of the adapter for connecting balanced stereo audio.

• Front Panel Connections – 6-pole terminal block.
• Rear Panel Connections - 6-pole terminal block.

For more information please click here.

Back to Top

WA-3N

Kramer Electronics Dual Mini Headphone Connector to Terminal Block Wallplate

A dual 3.5mm mini headphone connector to a 6-pole terminal block adapter for connecting dual audio stereo signals.

• Front Panel Connections - Dual 3.5mm (F).
• Rear Panel Connections - 6-pole terminal block.

For more information please click here.

Back to Top

WV-2N

Kramer Electronics Dual BNC to Terminal Block Adapter Wallplate

A dual BNC to 3-pole terminal block adapters for connecting two video sources.

• Front Panel Connections - Dual BNC (F).
• Rear Panel Connections - Dual 3-pole terminal block.

For more information please click here.

Back to Top

WX-1N

Kramer Electronics 15-pin HD to Terminal Block Adapter (VGA through UXGA) Wallplate

A 15-pin HD (VGA through UXGA) connector to a 6 + 2 terminal block connector for connecting a graphics source. The adapter includes a switch for ID bit control.

• Front Panel Connections - 15-pin HD (F).
• Rear Panel Connections - 6-pole and 2-pole terminal block.

For more information please click here.

Back to Top

WAS-1N

Kramer Electronics 4p + Mini Headphone Connectors to Terminal Block Adapter Wallplate

An s-Video (on a “4p” connector) and a 3.5mm mini headphone connector to two 3-pole terminal block, for connecting s-Video and stereo audio.

• Front Panel Connections - 3.5mm (F) and 4-pin Mini-DIN (F).
• Rear Panel Connections - Dual 3-pole terminal block.

For more information please click here.

Back to Top

WAV-1N

Kramer Electronics BNC + Mini Headphone Connector to Terminal Block Adapter Wallplate

A BNC and a 3.5mm mini headphone connector to two 3-pole terminal blocks, for connecting video and stereo audio.

• Front Panel Connections - 3.5mm (F) and BNC (F).
• Rear Panel Connections - Dual 3-pole terminal block.

For more information please click here.

Back to Top

WA-3N

Kramer Electronics Dual Mini Headphone Connector to Terminal Block Wallplate

A dual 3.5mm mini headphone connector to a 6-pole terminal block adapter for connecting dual audio stereo signals.

• Front Panel Connections - Dual 3.5mm (F).
• Rear Panel Connections - 6-pole terminal block.

For more information please click here.

Back to Top

WAS-1N

Kramer Electronics 4p + Mini Headphone Connectors to Terminal Block Adapter Wallplate

An s-Video (on a “4p” connector) and a 3.5mm mini headphone connector to two 3-pole terminal block, for connecting s-Video and stereo audio.

• Front Panel Connections - 3.5mm (F) and 4-pin Mini-DIN (F).
• Rear Panel Connections - Dual 3-pole terminal block.

For more information please click here.

Back to Top

WAV-1N

Kramer Electronics BNC + Mini Headphone Connector to Terminal Block Adapter Wallplate

A BNC and a 3.5mm mini headphone connector to two 3-pole terminal blocks, for connecting video and stereo audio.

• Front Panel Connections - 3.5mm (F) and BNC (F).
• Rear Panel Connections - Dual 3-pole terminal block.

For more information please click here.

Back to Top

WD-2F

Kramer Electronics Female DB-9 to Female DB-9 connection module Wallplate

Female DB-9 to Female DB-9 connection module

• Front Panel Connections - DB-9 (F)
• Rear Panel Connections - DB-9 (F)

For more information please click here.

Back to Top

WD-FM

Kramer Electronics Female DB-9 to Male DB-9 connection module Wallplate

Female DB-9 to Male DB-9 connection module

• Front Panel Connections - DB-9 (F)
• Rear Panel Connections - DB-9 (M).

For more information please click here.

Back to Top

WD-2M

Kramer Electronics Male DB-9 to Male DB-9 connection module Wallplate

Male DB-9 to Male DB-9 connection module

• Front Panel Connections - DB-9 (M)
• Rear Panel Connections - DB-9 (M).

For more information please click here.

Back to Top

WD-MF

Kramer Electronics Male DB-9 to Female DB-9 connection module Wallplate

Male DB-9 to Female DB-9 connection module

• Front Panel Connections - DB-9 (M)
• Rear Panel Connections - DB-9 (F).

For more information please click here.

Back to Top

Frame-2G

Kramer Electronics Wall Plate Insert Frame

• Front - 4WP Modules
• Rear - 4WP Modules
• Wall Plate

For more information please click here

Back to Top

WP-Frame

Kramer Electronics Wall Plate Insert Frame

A frame that can hold up to 3 WP passive devices.

• Holds 3 Wall Plate Inserts
• Wall Plate Size - Single gang

For more information please click here.

Back to Top

TBUS-3

Kramer Electronics Architectural Table Mount Interface

The Kramer Electronics TBUS-3 is a high quality anodized aluminum finished table-mount Interface system for boardrooms and conference rooms. Its attractive enclosure is designed to provide maximum connectivity in the smallest possible footprint.

• 4 Inputs - 15-Pin HD, 3.5mm, USB-A & RJ-45.
• Power Input - International, USA and European power sockets available.
• Cover - Manually opens & closes.
• Connector Depth - Adjustable.
• Size - 6.9" x 5.5" (176mm x 140.4mm) W, D (top plate)

For more information please click here.

Back to Top

TBUS-4

Kramer Electronics Architectural Table Mount Interface

The Kramer Electronics TBUS-4 is a high quality anodized aluminum finished table-mount interface system for boardrooms and conference rooms. Its attractive enclosure is designed to provide maximum connectivity in the smallest possible footprint.

• 8 Inputs - Two 15-Pin HD, two 3.5mm, two USB-A & two RJ-45.
• 2 Power Inputs - International, USA and European power sockets available.
• Wall Plate Insert Slots - Option to replace one of the power sockets with 2 wall plate Insert modules.
• Cover - Manually opens & closes.
• Connector Depth - Adjustable.
• Size - 9.6" x 5.5" (243mm x 140.4mm) W, D (top plate)

For more information please click here.

Back to Top